This product is available through authorized resellers.

Request Quote
Overview

Listen’s LR-100 Stationary RF Receiver/Power Amplifier is a stationary auditory assistance receiver with a built-in power amplifier. When used with a Listen transmitter, the LR-100 can deliver high quality audio for use in a variety of locations and applications — most commonly with a wireless audio distributed system. This unit has Listen’s signature Look&ListenTM LCD Display showing channel, lock, and battery level. A security cover protects auxiliary and receiver volume, adjustable squelch and trim controls. It has an balanced or unbalanced speaker wire output options. Multiple input options give this unit great flexibility. It’s powered by a 15 VAC/1000mA power input or 12 VDC battery. An antenna is needed for reception.

Includes

One (1) LR-100 Stationary RF Receiver/Power Amplifier
One (1) LR-100 manual
One (1) LA-201 15 VAC Power Supply
One (1) LA-124 90° Helical Antenna (216 MHz)
One (1) Hex Wrench

Highlights

  • Superior audio quality – 80 dB signal-to-noise ratio (SNR), setting the industry’s sound quality standard
  • 57 channels
  • 100 % Digital – Listen receivers are digitally-tuned so the transmission won’t drift
  • Programmability – Unneeded channels can be locked so this receiver will access only one or more channels of your choice
  • Look & Listen™ LCD shows channel, battery status, signal strength and programming information
  • Uses standard alkaline or nickel-metal hydride (NiMH) batteries
  • Built in SmartCharge™ won’t allow batteries to overcharge. Charging circuitry is conveniently built into Listen’s receivers
  • Drop in charging contacts for any of Listen’s many charging cases or a charging plug on the side of the unit
  • Adjustable squelch control
  • Selectable audio output
  • Multiple input options
  • Remote control capabilities
  • Optional 12 VDC input
  • Many accessory options make Listen products ideal for a wide range of applications
Configurations & Architectural Specs

Configurations

LR-100-072 Stationary RF Receiver/Power Amplifier (72 MHz)
LR-100-216 Stationary RF Receiver/Power Amplifier (216 MHz)

Architectural Specs

The Stationary RFReceiver/Power Amplifier shall be capable of receiving on 57 wide and narrow band channels in the frequency ranges of either 72 MHz or 216 MHz. The receiver shall be programmable to electronically lock out unneeded channels. The device shall have an adjustable squelch with an LED indication. The device shall have an audio frequency response of 50 Hz to 15k Hz, ‘±3 dB at 72 MHz, or of 50 Hz to 10 kHz, ‘±3 dB at 216 MHz. The signal to noise ratio shall be 80dB or greater. The device will have an integrated 15 watt power amplifier capable of driving an 8 ohm speaker. The device shall be rack mountable and shall have the capability of a remote antenna. The device shall incorporate an LCD display that indicates channel and RF signal strength. The Listen LR-100 is specified.

Product Specifications
Specification LR-100-216

Audio

Frequency Response System: 63 Hz - 10 kHz (±3 dB)
Signal-to-Noise Ratio 80 dB SQ enabled, 50 dB SQ disabled (A Weighted)
Distortion < 2% total harmonic distortion (THD) at 80% deviation
Input/s One (1) female XLR-1/4 in combo connector, balanced, 0 dBu nominal input level adjustable, +13 dBu maximum, impedance 600 ohmTwo (2) phono connectors, unbalanced, -10 dBu nominal input level adjustable, +7 dBu maximum, impedance 10k ohm band, 40 narrow band
Output/s One (1) male XLR, balanced, 0 dBu nominal output level, +16 dBu maximum, impedance 2k/10 Ohms (line/mic)Two (2) phono connectors, unbalanced, -10 dBu nominal output level, +2 dBu maximum, impedance 2k ohmOne (1) 3.5mm stereo connector, unbalanced, adjustable output level, +7 dBu maximum, impedance 10 ohmOne (1) detachable terminal block, bridged, adjustable output level, 15/10 watts (peak/RMS) continuous power with 4 ohm load

Controls

User Controls Front: Power, test tone on/off, channel up/down, input levels, mix level, contour, monitor volume controlRear: Audio output select (RX Only, RX + AUX, RX or AUX),Speaker (Output, Aux), switchable balanced output levelRemote Controls: Eight (8) position detachable terminal block, channel up, channel down, mute
Programming Unit can be programmed so that only desired channels are displayed to the user, channel selection can be locked by holding the SEEK button 5 seconds.

Indicators

LCD Channel designation, lock status, RF power level, programming (front panel)
Power LED Indicated by a green LED when on (front panel)
VU Meter Four (4) LED (three green, one red)
RF Power Indicated on the LCD (low, mid, high)
Squelch Green LED illuminates when the unit is squelched
Mute Green LED illuminates when the output audio is muted

RF

Frequency Range 216.025 - 216.987 MHz
Number of Channels 57 (19 wide band, 38 narrow band)
Sensitivity .6uV typical, 1 uV maximum for 12 dB SINAD
Frequency Accuracy ± .005% stability +32 ºF to +122 ºF (0 ºC to +50 ºC)
Antenna Type LA-124 90° Helical Antenna (216 MHz)
Antenna Connector BNC

Power

Power Supply Input 120 VAC, 60 Hz, 19 Watts
Power Supply Output 15 VAC, 1 Amp
Power Supply Connector .02 in (5.0 mm) OD, .01 in. (2.5 mm) ID, barrel type
Optional Battery 12VDC, connected via terminal block
Optional Battery Charging Trickle charge of optional 12VDC battery through terminal block connection
Power Supply Type In line power supply, Listen part number LA-201

Physical

Color Dark Grey with white silk screening
Unit Weight with Power Supply 4.2 lbs. (1.9 kg)
Shipping Weight 7.0 lbs. (3.2 kg)
Rack Mounting One (1) rack space height, 1/2 rack space wide, one (1) or two (2) receivers can be mounted in one rack space, optional rack mount (LA-326)
Dimensions (H x W x D) 1.75 x 8.50 x 9.13 in. (4.5 x 21.5 x 23 cm)
Unit Weight 2.8 lbs. (1.3 kg)

Environmental

Temperature - Operation -10 ºC (14 ºF) to +40 ºC (104 ºF)
Temperature - Storage -20 ºC (-4 ºF) to +50 ºC (122 ºF)
Relative Humidity 0 to 95% Relative Humidity, non condensing

Compliance

Power Supply Compliance UL Listed
Standards FCC Part 15, Part 90, Industry Canada
Used With
Accessories
FAQ
Q What is the function of SQ?
A To reduce noise of the systems, Listen offers a noise reduction technology called ListenSQ™. Both the transmitter and receiver must have SQ on to achieve the desired results. If you are planning to use this product with older Listen systems or equipment not manufactured by Listen, you should disable SQ.
Q How many LR-100's can I use in a system?
A As many as you need, the number is endless.
Q Can I interface this to an amplifier or powered speaker?
A Yes, both.
Q Do I run the speakers in series or parallel?
A It's your choice. However minimum impedance attached to LR-100 speaker amplifier must be greater than 4 ohms.
Copyright © 1998 - 2019 Listen Technologies Corporation. All rights reserved.
Listen, ListenPoint and related marks and logos are registered trademarks of Listen Technologies Corporation. Terms of Use | Privacy Policy
Listen Technologies
Loading...
Loading...
Loading...
Loading...
Loading...